SCO OpenServer 6 Integration Specification

Enter the desired system name (max 8 characters, no punctuation)
Enter the desired DNS domain name

Security Profile
High (Above C2)
Improved (C2)
Traditional (default)
Low

Time Zone
Eastern
Central
Mountain
Pacific
Other (specify in special instructions at the end)

Day Light Saving Time Observed ?
Yes
No

If disks are in a RAID array, setup this RAID level:

RAID-1 (mirror protection)
RAID-0+1 (mirror protection + striping for performance if 4 or more drives)
RAID-5 (data protection at lower cost but lower performance than RAID-1 or 0+1)
N/A (I'm sure there is no RAID to be setup)
RAID options that I am expecting:
Channel Separation (Much better RAID-1 or 0+1 reliability if at least 2 RAID channels)
Stand-by drive (Additional drive to replace a failed drive. The replacement will be automatic on the Adaptec 2120s/2200s but not on the 3200/3210/3400.)

Disk Drive 0 (where the Operating System will be installed)

GB: Size of root filesystem in GB (min 5 GB recommended)
MB: Size of SWAP in MB or enter "default" to use DTR recommendations:

     256 MB RAM =>  512 MB swap
     512 MB RAM => 1024 MB swap (1 GB)
       1 GB RAM => 1536 MB swap (1.5 GB)
       2 GB RAM => 2048 MB swap (2 GB)
       4 GB RAM => 3072 MB swap (3 GB)
     Note: some applications recommend additional swap space per user

Size of /u in GB or % allocation of the remaining disk 0 space to use (e.g. 50%) default is 100%
MB: Enter size of /tmp in MB if you want /tmp to be a separate memfs filesystem, which will provide fast access to /tmp since it will be memory resident BUT all files & directories in /tmp will disappear every reboot. /tmp must be memfs to use emergency_disk (but not BackupEDGE or Lone-Tar). Leave this field blank to make /tmp part of the root filesystem on disk, which is the DTR default recommendation.
MB: Enter size of /var/tmp in MB if want /var/tmp to be a separate memfs filesystem for better performance and auto-clear on reboot if you add system packages a lot. If both /tmp and /var/tmp are memfs, they will share the combined memory. Leave this field blank to make /var/tmp part of the root filesystem on disk, which is the DTR default recommendation.
Enter the mount point(s) and % allocation of disk 0 to use for up to 6 other filesystems on drive 0 in addition to /u.


Note: A RAID subsystem will usually appear to be one big drive 0.

filesystem mount point(s) (and % allocation)

filesystem mount point(s) (and % allocation)

filesystem mount point(s) (and % allocation)

filesystem mount point(s) (and % allocation)

first NIC card (ethernet) or leave the default DTR test values: 10.1.1.200 255.0.0.0
IP address
Network mask
Default gateway or leave blank to set this later
DNS server or leave blank to set this later

second NIC card (if any) or leave the default DTR test values: 192.168.20.100 255.255.255.0
IP address (cannot be in same subnet as first NIC) or enter BACKUP if you want the 2nd NIC to take automatically take-over for the first NIC if it dies.
Network mask

The Intel Advanced IMM (Intel Mgmt Module) is an extra cost option that provides an additional ethernet port that can be used, via telnet or browser, to check the hardware health, fans, power supply(s). Allows rebooting a down system. Allows remote KVM for checking/changing the bios, bios raid, watching the system boot, normal login and applications, and seeing the last error even if hung with screen saver on.
Adv IMM IP address (cannot match any other IP in this server)
Adv IMM Network mask
Adv IMM Default Gateway address
Adv IMM admin user name
Adv IMM admin password

Email subsystem
mmdf
sendmail (DTR default)

root password (should not be a dictionary word or name)

COM1 serial port, I usually prefer
modem, if ordered
UPS cable, if UPS ordered
UniBasic Passport device, if ordered

COM2 serial port, I usually prefer
modem, if ordered
UPS cable, if UPS ordered
UniBasic Passport device, if ordered

If any Digi PortServers are on the order
Install RealPort SW
IP, NetMask, Gateway for first PortServer
    (Add IP, NetMask, Gateway for other PortServers under Special Instructions below)

Note: Extra-cost packages (such as Advanced File & Print Server, BackupEDGE, Development System (C compiler), Lone-Tar, Merge, and SMP) are not listed above. They will be installed automatically if you have purchased them with this system.

Enter any other special instructions or requests: (Please press ENTER at the end of each line so no line is too long. You may copy/paste into this box as it will hold thousands of characters of input.

Please review all of the above information and then click the Submit button to send it to the DTR Integration group. You do not need to do anything further after you click Submit below.