SCO OpenServer 5 Integration Specification

form date: 5-17-2011

If you have ordered a SCO OpenServer 5 system to be integrated by DTR, please fill in the following blanks and then click the Submit button found at the buttom of this page.

Enter your name (REQUIRED)
Enter your company name (REQUIRED)
Enter your email address (REQUIRED) in case we have questions
Type an identifying phrase so we will know which system or site this info applies to (eg end-user company name, address, and/or server function)

Enter the desired system name (max 8 characters, no punctuation)
Enter the desired local domain name for this SCO server

Mouse and GUI settings
Mouse and GUI enabled (DTR default)
Connect mouse but disable GUI
No mouse and No GUI ever

If we integrate the system with a mouse and you remove the mouse later, the system bios may get confused, reassign IRQ's and refuse to boot. To prevent such problems, we recommend that you always connect the mouse and just disable the GUI, if desired, so it can be re-enabled later. For example, if you have an Adaptec 3200 RAID controller, the GUI Storage Manager utility provides information and options not available elsewhere.

Time Zone
Eastern
Central
Mountain w/ daylight savings
Mountain w/o daylight savings
Pacific
Other (specify in special instructions at the end)

If disks are in a RAID array, setup this RAID level:

Warning: Many raid cards today have no alarm if a drive fails. SAS/SATA RAID on SCO 5 has no alarm and no utility to check the RAID status while SCO 5 is running. An LED on the back of the machine will change from blinking green to solid amber if there is a fault condition. Choose SCSI RAID on SCO 5 if you want some sort of notification of a drive failure.

Disk Drive 0 (or Array 0 if raid) (where the Operating System will be installed)

     512 MB RAM => 1 GB swap
       1 GB RAM => 2 GB swap
       2 GB RAM => 3 GB swap
       4 GB RAM or more => 4 GB swap (max allowed)

Name(s) of other filesystem mount point(s) on drive 0 (and size in GB or % allocation of remaining disk space), if any (e.g. /u 50%, /u2 50%)
Note: A RAID subsystem will usually be setup as one large array 0. If so, leave the following drive questions blank.

drive 1 (or Array 1 if raid) (if present)

drive 2 (or Array 2 if raid) (if present)

drive 3 (or Array 3 if raid) (if present)

drive 4 (or Array 4 if raid) (if present)

first NIC card (ethernet) or leave the default DTR test values: 10.1.1.200 255.0.0.0
IP address
Network mask
Default gateway or leave blank to set this later
DNS server or leave blank to set this later

second NIC card (if any) or leave the default DTR test values: 192.168.20.100 255.255.255.0
IP address (cannot be in same subnet as first NIC)
Network mask

Email subsystem
mmdf
sendmail (DTR default)

Security
Low
Traditional (default)
Improved (C2)
High (Above C2)

COM1 serial port, I usually prefer
test only but leave unconfigured
modem, if ordered
UPS cable, if UPS ordered
UniBasic Passport device, if ordered

COM2 serial port is not available on many systems. If available, I usually prefer
test only but leave unconfigured
modem, if ordered
UPS cable, if UPS ordered
UniBasic Passport device, if ordered

If any Digi PortServers are on the order
Install RealPort SW
IP, NetMask, Gateway for first PortServer
(Add IP, NetMask, Gateway for other PortServers under Special Instructions below)

root password (You MUST enter a password. It should not be a dictionary word or name)

Optional package(s)
Samba (free)

Note: Extra-cost packages (such as Advanced File & Print Server, BackupEDGE, Development System (C compiler), Lone-Tar, Merge, and SMP) are not listed above. They will be installed automatically if you have purchased them with this system.

Enter any other special instructions or requests: (Please press ENTER at the end of each line so no line is too long. You may copy/paste into this box as it will hold thousands of characters of input.

Please review all of the above information and then click the Submit button to send it to the DTR Integration group. You do not need to do anything further after you click Submit below.